Michelin replacement tires owner's manual and warranty

Costco · Official agreement

Read the agreement

51 of 106 cards in Security & Safeguards

Security & Safeguards · Context

Tire failures can follow punctures, impact, inflation, overloading or distortion

Michelin warns that any tire may fail after an improperly repaired puncture, impact damage, improper inflation, overloading, a crack, a bulge or other distortion, or other conditions resulting from use or misuse. Rapid air loss or tread and belt detachment may increase the risk of injury, death or property damage. Michelin says the risk is reduced by thoroughly reading and following this manual, the vehicle owner's manual, the tire information placard and tire sidewall safety information.

Supporting quotations

TIRE FAILURE – SAFETY WARNING
Any tire may fail as a result of an improperly repaired puncture, impact damage, improper inflation, overloading, a crack, a bulge or other distortion, or other conditions resulting from use or misuse.
Tire failures, such as a rapid air loss or a tread and belt detachment may increase risk of injury, death, or property damage.

Security & Safeguards · Procedure

After a tire failure, coast straight and brake gently rather than hard

On a tire failure, which may bring a loud noise, vibration or a pull toward the failed tire, Michelin says not to brake or turn the steering wheel abruptly. The driver should slowly release the accelerator, hold the wheel firmly to stay in lane, and once the vehicle has slowed and is controlled, brake gently, pull onto the shoulder and stop in the safest place. All tires should then be inspected. A flat, low, detached or otherwise damaged tire is replaced with a properly inflated spare after inspecting the spare; bumps, bulges or cracks call for inspection by a tire professional and no further driving on that tire. If there is no other option, Michelin says to drive as slowly and cautiously as possible until towing or mechanical help is available, and with an improperly inflated spare only as slowly as safely possible until it can be inflated and checked.

Supporting quotations

CONTROLLING A VEHICLE WHEN A TIRE FAILURE OCCURS
If a tire failure occurs, you may hear a loud noise, feel a vibration, or feel the vehicle pull toward the side of the failed tire.
If that happens, DO NOT BRAKE OR ABRUPTLY TURN THE STEERING WHEEL. Instead, slowly remove your foot from the accelerator and hold the steering wheel firmly while steering to remain in your lane.
Once the vehicle has slowed and is fully in your control, apply the brakes gently, safely pull over to the shoulder, and come to a stop in the safest location possible.
If any tire, including the spare, has bumps, bulges, cracks, or other visible damage, do not resume driving with that tire.

Qualifications & exceptions

  • Applies when the failure is heard, felt as vibration or felt as a pull toward the failed tire.
  • Driving on a damaged tire is limited to having no other option.

Security & Safeguards · Procedure

Correct pressures come from the placard or a Michelin retailer, never above the sidewall maximum

For tires that came as original equipment, the recommended operating pressures are on the vehicle's tire information placard, located in the door jamb, inside the fuel hatch or on the glove compartment door. For replacement tires, the owner asks a Michelin tire retailer for the correct pressure, and falls back to the placard. Those pressures are a minimum to maintain, and the Maximum Pressure rating on the tire sidewall must never be exceeded. Rear and front pressures may differ, and the Maximum Pressure rating is normally not equal to the placard pressure.

Supporting quotations

PROPER INFLATION
WARNING ON IMPROPERLY INFLATED TIRES.
DO NOT DRIVE UNNECESSARILY
DRIVING ON ANY TIRE THAT DOES NOT HAVE THE CORRECT INFLATION PRESSURE IS DANGEROUS
An underinflated tire builds up excessive heat that may result in sudden tire failure and an accident.
These inflation pressures must be maintained as a minimum. Never exceed the Maximum Pressure rating stated on the tire sidewall. Note that proper inflation pressures for rear tires may differ from proper inflation pressures for front tires. The Maximum Pressure rating on the tire is normally not equal to the placard pressure.

Qualifications & exceptions

  • The placard pressures are a minimum; the sidewall Maximum Pressure rating is a ceiling.
  • Rear tire pressures may differ from front tire pressures.
  • The warning section also tells drivers: “DO NOT DRIVE UNNECESSARILY”.

Security & Safeguards · Procedure

Inflation is checked cold at least monthly and before long trips

Michelin says failure to maintain correct inflation may cause improper vehicle handling, rapid and irregular tire wear, sudden tire failure, loss of vehicle control and an accident. Pressures should therefore be checked at least once each month and before every long-distance trip, for all tires including sealant types and self-supporting tires, which lose inflation as readily as any other tire if not maintained. Checks are made before the tires have been driven on, or after they cool to ambient temperature, because driving raises pressure and the recommended pressures are for tires not heated by recent driving.

Supporting quotations

CHECK THE COLD INFLATION PRESSURE IN ALL YOUR TIRES, INCLUDING THE SPARE, AT LEAST ONCE EACH MONTH
Failure to maintain correct inflation may result in improper vehicle handling and may cause rapid and irregular tire wear, sudden tire failure, loss of vehicle control, and an accident.
Therefore, inflation pressures should be checked at least once each month and before every long-distance trip.
Pressures should be checked before the tires have been driven on or after they have been allowed to cool down to the ambient air temperature.

Qualifications & exceptions

  • Applies to all tires, including sealant types and self-supporting tires.
  • Pressures are for cold tires, before driving or after cooling.

Security & Safeguards · Procedure

A pressure gauge, not a visual check, shows whether a tire is properly inflated

Tires must be checked monthly with a tire pressure gauge, because it is impossible to determine by looking at a tire whether it is properly inflated, and almost impossible to feel or hear underinflation or overinflation. Michelin suggests keeping an accurate, inexpensive gauge in the glove box or trunk and using it monthly and as otherwise needed.

Supporting quotations

UNDERINFLATION AND OVERINFLATION MUST BE CHECKED WITH A TIRE PRESSURE GAUGE
Tires must be checked monthly with a tire pressure gauge. It is impossible to determine whether tires are properly inflated by simply looking at them.
You should keep one in your vehicle’s glove box or trunk and use it monthly and as otherwise needed.

Security & Safeguards · Context

Deflated PAX and ZP tires handle differently and tolerate only limited low-pressure running

A vehicle running a deflated PAX System or Self-Supporting Zero Pressure tire handles differently from one on normally inflated tires, so drivers should avoid high speeds and hard cornering whenever a low-pressure warning activates. These tires can still build excessive heat when run underinflated for a long time, and how long they perform at low or zero inflation depends on the severity of the air loss, ambient temperature, speed and operating conditions, with hard braking, cornering and sharp maneuvers greatly reducing that time. Continuous use of an underinflated tire may lead to sudden tire failure and an accident, and a tire at low or zero pressure that begins to vibrate or affects handling should be replaced immediately with the temporary spare.

Supporting quotations

MICHELIN® PAX® SYSTEMTM TIRES AND SELF SUPPORTING ZERO PRESSURETM (ZP) TIRES AT LOW OR ZERO INFLATION
The handling characteristics of a vehicle with a deflated PAX® System tire or Self-Supporting Zero Pressure (ZP) tire (whether front or rear) are not the same as those of a vehicle with normally inflated tires. Avoid high speeds and hard cornering whenever a low-pressure warning is activated.
Even a MICHELIN PAX System tire or Self-Supporting Zero Pressure (ZP) tire can build up excessive heat when run underinflated for an extended period of time.
If a tire at low or zero pressure begins to vibrate or cause difficulty in vehicle handling, replace it immediately with the temporary spare.

Qualifications & exceptions

  • When PAX or ZP tires are original equipment, the vehicle owner's manual has the low pressure warning system details.
Also annotated in the same passage (1)

Security & Safeguards · Procedure

After a low-pressure warning on PAX or ZP tires, check all four tires with a gauge

PAX System tires depend on a functioning, correctly calibrated onboard tire pressure monitoring system. After any low-pressure warning, Michelin says to inspect the PAX or ZP tires visually and check all four with a pressure gauge. If the pressure is at or below 18 PSI, the tire goes to the nearest Authorized PAX System retailer or Michelin tire retailer for demounting and a thorough internal inspection. If no damage is visible and pressure is above 18 PSI, the tire is reinflated and checked again when cool, and a tire that has lost more than 5 PSI since the previous check goes in for inspection at once.

Supporting quotations

MICHELIN® PAX® SYSTEMTM TIRES AND SELF SUPPORTING ZERO PRESSURETM (ZP) TIRES AT LOW OR ZERO INFLATION
The PAX System™ requires a functioning, correctly calibrated onboard vehicle tire pressure monitoring system (TPMS) to monitor the inflation and alert the driver when a low pressure event occurs.
If the tire pressure is at or below 18 PSI, proceed to the nearest Authorized PAX System Retailer for PAX® tires or a Michelin tire retailer for ZP tires (or a representative of your vehicle manufacturer if advised to do so in your vehicle owner’s manual) and have the tire demounted and thoroughly inspected for possible internal damage.
When tires have cooled, check inflation again. If any tire has lost more than 5 PSI from the previous pressure check, have the tire inspected at once by an authorized PAX System Retailer for PAX tires or a Michelin tire retailer (or representative of your vehicle manufacturer if your vehicle owner’s manual so advises.)

Qualifications & exceptions

  • The 18 PSI threshold triggers demounting and internal inspection.
  • A loss of more than 5 PSI since the previous check requires immediate inspection.
Also annotated in the same passage (2)

Security & Safeguards · Restriction or exception

ZP and PAX tires void the warranty without approved warning systems and correct wheels

MICHELIN Self-Supporting Zero Pressure (ZP) tires must be used only with an operational, Michelin-approved low tire pressure warning system, and PAX System tires only with a tire pressure monitoring system approved by the vehicle manufacturer; otherwise all provisions of the limited warranty are void. ZP tires marked SH-M can only be mounted on special SH-M wheels, and mounting one on a standard wheel voids the warranty and could make the tire unserviceable at low or zero pressure, with serious injury or death possible. Michelin points to its retailers and phone numbers for the lists of approved systems, and says the recommended operating pressures, which must be maintained as a minimum and never exceed the sidewall Maximum Pressure, come from the vehicle placard, a Michelin retailer for ZP tires or a PAX System retailer for PAX tires.

Supporting quotations

MICHELIN® SELF-SUPPORTING ZERO PRESSURE™ (ZP) TIRES MUST BE USED ONLY WITH AN OPERATIONAL, MICHELIN APPROVED, LOW TIRE PRESSURE WARNING SYSTEM. Otherwise, all provisions of the limited warranty are void.
DO NOT MOUNT A TIRE WITH THE SH-M DESIGNATION ON THE SIDEWALL ON A STANDARD WHEEL. DOING SO VOIDS THIS LIMITED WARRANTY AND COULD CAUSE THE TIRE TO BECOME UNSERVICEABLE AT LOW OR ZERO PRESSURE, RESULTING IN SERIOUS PERSONAL INJURY OR DEATH.
PAX SYSTEM TIRES ARE TO BE USED ONLY WITH AN OPERATIONAL TIRE PRESSURE MONITORING SYSTEM (TPMS) APPROVED BY THE VEHICLE MANUFACTURER FOR USE WITH THE PAX SYSTEM. Otherwise, all provisions of the limited warranty are void.
Recommended operating pressures will be provided by a Michelin tire retailer for self-supporting ZP tires. Recommended operating pressure for PAX System Tires will be provided by a PAX System retailer. These inflation pressures must be maintained as a minimum. Never exceed the Maximum Pressure rating shown on the tire sidewall.

Qualifications & exceptions

  • Approved warning systems are required; otherwise all warranty provisions are void.
  • SH-M designated ZP tires require SH-M wheels.
  • Recommended pressures are a minimum; the sidewall Maximum Pressure rating is the ceiling.

Not stated here

  • The lists of approved systems are not reproduced in this manual.
Also annotated in the same passage (1)

Security & Safeguards · Procedure

Check all four tires as soon as possible after a PAX or ZP low-pressure warning

Michelin tells owners of PAX System and ZP tires to check inflation pressures as soon as possible after a low pressure warning. After visually inspecting the tires, the owner checks all four with a pressure gauge and keeps the vehicle's tire pressure monitoring system functioning and correctly calibrated. At or below 18 PSI, the tire goes to the nearest Authorized PAX System retailer or Michelin tire retailer for demounting and internal inspection; above 18 PSI with no visible damage, it is reinflated and rechecked when cool. A loss of more than 5 PSI since the previous check requires immediate inspection, since delay may cause irreparable damage and sudden tire failure.

Supporting quotations

FOR MICHELIN® PAX SYSTEMTM TIRES/SELF-SUPPORTING ZERO PRESSURE (ZP) TIRES CHECK INFLATION PRESSURES AS SOON AS POSSIBLE FOLLOWING A LOW PRESSURE WARNING
The PAX System™ requires a functioning, correctly calibrated onboard vehicle tire pressure monitoring system (TPMS) to monitor the inflation and alert the driver when a low pressure event occurs.
If the tire pressure is at or below 18 PSI, proceed to the nearest Authorized PAX System Retailer for PAX® tires or a Michelin tire retailer for ZP tires (or a representative of your vehicle manufacturer if advised to do so in your vehicle owner’s manual) and have the tire demounted and thoroughly inspected for possible internal damage.
If any tire has lost more than 5 PSI from the previous pressure check, have the tire inspected at once by an authorized PAX System Retailer for PAX tires or a Michelin tire retailer (or representative of your vehicle manufacturer if your vehicle owner’s manual so advises.) Failure to do so may cause irreparable damage to the tire and result in sudden tire failure and an accident.

Qualifications & exceptions

  • 18 PSI or less means demounting and internal inspection.
  • More than 5 PSI lost since the previous check means immediate inspection.
Also annotated in the same passage (1)

Security & Safeguards · Procedure

TPMS warns of low pressure but monthly manual checks still apply

A Tire Pressure Monitoring System monitors tire pressure and signals the driver when pressure falls below a predetermined level. Michelin says it should not replace monthly manual pressure checks of all four tires and the spare with a pressure gauge. The recommended pressure is the vehicle manufacturer's, found in the vehicle owner's manual and on the placard in the door jamb, fuel hatch or glove compartment door. Plus-size tires that need higher pressure require the TPMS to be recalibrated by the tire dealer or installer, and TPMS monitoring problems should be taken to the vehicle owner's manual and the vehicle manufacturer.

Supporting quotations

TIRE PRESSURE MONITORING SYSTEMS (TPMS):
Your vehicle is likely equipped with a Tire Pressure Monitoring System (TPMS) that is designed to monitor the pressure of tires mounted on your vehicle and sends a signal to the driver if a tire pressure falls below a predetermined level. A TPMS should not replace monthly manual pressure checks for all four tires and the spare.
You should check inflation in all your tires, including the spare, once each month and before every long trip.
If you have plus-size tires that require a higher inflation pressure, your tire pressure monitoring system will require re-calibration to the new proper inflation pressure.

Qualifications & exceptions

  • Applies to vehicles likely equipped with TPMS.
  • The spare is checked as well as the four road tires.

Security & Safeguards · Restriction or exception

Never spin wheels above 35 mph or stand near a spinning tire

Michelin warns against spinning wheels at more than 35 mph (55 km/h) as shown on the vehicle's speedometer, and against letting anyone stand near or behind a spinning tire. Excessive speed in a free-running, unloaded tire can make it explode from centrifugal force, and the released energy may cause serious physical injury or death. In mud, sand, snow, ice or another slippery condition the driver should avoid excessive wheel spin, since accelerating the motor, particularly with an automatic transmission, may spin a drive tire that has lost traction beyond its speed-enduring capability. The same applies when balancing a drive tire/wheel assembly on the vehicle using the engine.

Supporting quotations

TIRE SPINNING
WARNING
NEVER SPIN WHEELS ABOVE 35 MPH. NEVER ALLOW ANYONE TO STAND NEAR A SPINNING WHEEL.
Excessive speed in a free-running, unloaded tire can cause it to “explode” from centrifugal force. The energy released by such an explosion may cause serious physical injury or death. Never allow anyone to stand near or behind a spinning tire.
When in mud, sand, snow, ice, or another slippery condition, do not engage in excessive wheel spin.

Qualifications & exceptions

  • The limit is 35 mph (55 km/h) as indicated on the vehicle's speedometer.
  • Applies in mud, sand, snow, ice and other slippery conditions and when balancing a drive tire on the vehicle.

Security & Safeguards · Context

High speed driving leaves less room for hazards even at correct inflation

Michelin says correct inflation pressure is especially important at high speed, yet even with correct pressure a road hazard is harder to avoid at high speed and contact with it is more likely to damage the tire than at lower speed. Driving fast also reduces the reaction time available to avoid accidents and bring the vehicle to a safe stop.

Supporting quotations

HIGH SPEED DRIVING IS DANGEROUS
Correct inflation pressure is especially important. However, at high speeds, even with the correct inflation pressure, a road hazard is more difficult to avoid, and if tire contact is made with it, there is a greater chance of causing tire damage than at a lower speed. Moreover, driving at high speed reduces the reaction time available to avoid accidents and bring your vehicle to a safe stop.

Security & Safeguards · Restriction or exception

Do not drive faster than the tires' speed ratings or the legal limits

Michelin warns against driving at speeds faster than the speed ratings for the tires and against ever exceeding legal speed limits or speeds reasonable for the driving conditions. Exceeding the maximum speeds shown for each type of MICHELIN tire causes the tire to build up excessive heat, which can damage it and lead to sudden tire failure and rapid air loss; failing to control the vehicle when one or more tires lose air rapidly can lead to an accident. In any case, the driver should not exceed reasonable speeds as indicated by the legal limits and driving conditions.

Supporting quotations

WARNING
DO NOT DRIVE AT SPEEDS FASTER THAN THE SPEED RATINGS FOR YOUR TIRES. NEVER EXCEED LEGAL SPEED LIMITS OR SPEEDS REASONABLE FOR THE DRIVING CONDITIONS.
Exceeding the maximum speeds shown on the following page for each type of MICHELIN® tire will cause the tire to build up excessive heat, which can cause tire damage that could result in sudden tire failure and rapid air loss.
In any case, you should not exceed reasonable speeds as indicated by the legal limits and driving conditions.

Qualifications & exceptions

  • Legal speed limits and speeds reasonable for the driving conditions remain upper bounds.
Also annotated in the same passage (1)

Security & Safeguards · Context

Speed symbols L through H cover 75 to 130 mph

Michelin's speed rating table pairs each speed symbol with its speed in kilometres per hour and miles per hour: L 120 km/h (75 mph), M 130 (81), N 140 (87), P 150 (94), Q 160 (100), R 170 (106), S 180 (112), T 190 (118), U 200 (124) and H 210 (130).

Supporting quotations

| Speed Symbol | | Speed (km/h) | Speed (mph) |
| L | | 120 | 75 |
| M | | 130 | 81 |
| N | | 140 | 87 |
| P | | 150 | 94 |
| Q | | 160 | 100 |
| R | | 170 | 106 |
| S | | 180 | 112 |
| T | | 190 | 118 |
| U | | 200 | 124 |
| H | | 210 | 130 |

Security & Safeguards · Context

Speed symbols V through (Y) run from 149 mph upward

The same table continues with V 240 km/h (149 mph), W and ZR 270 (168), Y 300 (186) and (Y) above 300 km/h, with the manual directing the reader to consult the tire manufacturer above 186 mph.

Supporting quotations

| V | | 240 | 149 |
| W | ZR | 270 | 168 |
| Y | | 300 | 186 |
| (Y) | | Above 300 | Above 186 (consult tire manufacturer) |

Security & Safeguards · Context

A speed rating states the speed at which a tire can carry a load

The manual defines the speed rating of a tire as indicating the speed, or range category of speeds, at which the tire can carry a load under specified service conditions. The extracted text sets this definition out in fragments around the table, so the sentence is reassembled from the pieces quoted here rather than read as continuous prose in one block.

Supporting quotations

The speed rating of a tire indicates the speed
(or range category of
at which speeds) tire can carry under specified
the
a load
service

Not stated here

  • The PDF text extraction interleaves this definition with the speed table, so the sentence is split across blocks and its original typography is not visible.

Security & Safeguards · Context

The speed rating system runs from letters A to Z

Michelin describes the speed rating system used today as developed in Europe to categorize tires into standardized speeds, with a letter from A to Z symbolizing a tire's certified speed rating and ranging from 5 km/h (3 mph) to above 300 km/h (186 mph). The chart on the page states the top speed for which a tire is certified. The extracted text breaks this discussion into fragments around the table.

Supporting quotations

The speed conditions.
rating system used today
was developed in Europe in response to the need
to categorize tires into
standardized speeds.
A letter from A to Z
symbolizes a tire’s certified
speed rating, ranging from 5 km/h (3 mph) to
300 km/h above
(186
mph). This rating system
(see chart on this page)
describes the top speed
for which a tire is certified.

Not stated here

  • The extracted fragments mix the end of the definition with the start of this discussion, so word order across blocks is uncertain.

Security & Safeguards · Context

The Unlimited V, Limited V and Z or (Y) categories mark added speed steps

Michelin explains that when the rating system was developed, the Unlimited V category above 210 km/h (130 mph) was the top speed rating. New tires in that category led to the Limited V category at 240 km/h (149 mph) and the Z or (Y) rating as the top rating, with W and Y limited speed symbols added as higher speed categories. The manual says to always consult the tire manufacturer for the maximum speed of Unlimited Z or (Y) tires, and that a tire's speed rating is identified as part of its sizing or service description. Exceeding the lawful speed limit is neither recommended nor endorsed.

Supporting quotations

When this speed rating was originally system developed, the Unlimited
As manufacturers made more tires that fit into this category, it was necessary to better regulate performance at standardized speeds to help ensure safety.
Always consult the tire manufacturer for the maximum speed of Unlimited Z or (Y) tires. Speed rating is identified as a part of the tire’s sizing or service description. Exceeding the lawful speed limit is neither recommended nor endorsed.

Security & Safeguards · Procedure

The service description combines load index and speed rating

Except for Unlimited Z, the ratings incorporate the speed symbol and load index as the tire's service description. The manual decodes the example 205/60R15 91V: 205 is the section width in millimetres, 60 the aspect ratio, R radial construction, 15 the rim diameter in inches, and 91V the service description carrying the load index and speed rating. Where Z appears in the size description together with the service description, the maximum speed is indicated by the service description.

Supporting quotations

In the latest attempt to standardize tire designations, all ratings except Unlimited Z incorporate the speed symbol and load index as the tire’s service description.
For Example:
205/60R15 91V
Section Width in Millimeters 205 =
60 = Aspect Ratio
R = Radial Construction
15 = Rim Diameter in Inches Service Description (Load Index and Speed Rating) 91V = “Z” Rated Tires
When “Z” appears in the size description with the service description, the maximum speed is indicated by the service description.

Qualifications & exceptions

  • Unlimited Z ratings are the exception to the service-description rule.

Security & Safeguards · Context

Z designations mark tires capable of more than 149 mph

The manual lists example Z designations (P275/40ZR17, P275/40R17 93Y, P275/40ZR17 93Y and P275/40ZR17 (93Y)) next to a maximum-speed column, with a note to consult the tire manufacturer. It states that a Z may appear in the size designation for tires capable of more than 240 km/h (149 mph), and must appear with Y in parenthesis in the service description for tires above 300 km/h (186 mph), giving 275/40ZR18 (99Y) as an example. Where there is no service description, the manufacturer is consulted for maximum speed.

Supporting quotations

Examples:
Tire Designation
P275/40ZR17
P275/40R17 93Y
P275/40ZR17 93Y
P275/40ZR17 (93Y)
*Consult Tire Manufacturer
Maximum Speed
Above 240 km/h (149 mph)* 300 km/h (186 mph)
300 km/h (186 mph)
Above 300 km/h (186 mph)*
For tires having a maximum speed capability above 240 km/h (149 mph), a “Z” may appear in the size designation.
For tires having a maximum speed capability above 300 km/h (186 mph), a “Z” must appear in the size designation and the service description must include Y in parenthesis. Example: 275/40ZR18 (99Y). Consult the tire manufacturer for maximum speed when there is no service description.

Qualifications & exceptions

  • A Z mark alone means above 149 mph; above 186 mph requires Z plus Y in parenthesis.

Not stated here

  • The PDF extraction separates the example designations from their maximum-speed column, so which example row carries which speed is not reliable from the stored text.

Security & Safeguards · Restriction or exception

Speed ratings assume sound, correctly inflated tires and do not authorize unsafe driving

Michelin says speed ratings rest on laboratory tests that relate to road performance but do not apply if the tires are underinflated, overloaded, worn out, damaged, altered, improperly repaired or retreaded. A rating does not imply that a vehicle can safely be driven at the tire's maximum speed, especially in adverse road or weather conditions or with an unusual vehicle. Highway passenger tires without a speed symbol are rated at 105 mph (170 km/h), light truck highway tires without a symbol at 87 mph (140 km/h), and winter tires without a symbol or with Q at 100 mph (160 km/h), while winter tires with a symbol follow the symbol. Retreaded tire ratings are assigned by the retreader and replace the manufacturer's ratings. A replacement tire's speed rating should be equal to or higher than the original equipment rating; if it is lower, the vehicle top speed becomes limited to the lower rating and the customer must be told about the new restriction and possible handling impact.

Supporting quotations

Exceeding the maximum speeds shown on the following page for each type of MICHELIN® tire will cause the tire to build up excessive heat, which can cause tire damage that could result in sudden tire failure and rapid air loss.
Speed ratings are based on laboratory tests that relate to performance on the road, but are not applicable if tires are underinflated, overloaded, worn out, damaged, altered, improperly repaired, or retreaded.
Michelin highway passenger tires that do not have a speed symbol on the sidewall have a maximum speed rating of 105 mph (170 km/h). Light truck highway tires that do not have a speed symbol on the sidewall of the tire have a maximum speed rating of 87 mph (140 km/h). Michelin winter tires that do not have a speed symbol on the sidewall or tires with Q symbols have a speed rating of 100 mph (160 km/h).
The speed and other ratings of retreaded tires are assigned by the retreader and replace the original manufacturer’s ratings.
IMPORTANT: The replacement tire speed rating should be equal to or higher than the OEM tire speed rating. If a lower speed rated tire is selected, then the vehicle top speed becomes limited to that of the lower speed rating selected. The customer must be informed of the new speed restriction and that the vehicle’s handling may be adversely impacted.

Qualifications & exceptions

  • Ratings do not apply to underinflated, overloaded, worn out, damaged, altered, improperly repaired or retreaded tires.
  • A replacement tire's rating should be equal to or higher than the original equipment rating.
Also annotated in the same passage (2)

Security & Safeguards · Restriction or exception

Tires without a speed symbol still have fixed maximum speeds

Michelin highway passenger tires without a speed symbol on the sidewall have a maximum speed rating of 105 mph (170 km/h), light truck highway tires without a symbol 87 mph (140 km/h), and winter tires without a symbol or with a Q symbol 100 mph (160 km/h); winter tires with a symbol follow the symbol. The manual adds that a tire may be speed-rated yet no vehicle should be operated unsafely or unlawfully, and that ratings are not applicable to underinflated, overloaded, worn out, damaged, altered, improperly repaired or retreaded tires. A replacement tire's speed rating should equal or exceed the original equipment rating; a lower rating limits the vehicle's top speed, and the customer must be told about the restriction and possible handling impact.

Supporting quotations

Although a tire may be speed-rated, no vehicle should be operated in an unsafe or unlawful manner.
Speed ratings are based on laboratory tests that relate to performance on the road, but are not applicable if tires are underinflated, overloaded, worn out, damaged, altered, improperly repaired, or retreaded.
Michelin highway passenger tires that do not have a speed symbol on the sidewall have a maximum speed rating of 105 mph (170 km/h). Light truck highway tires that do not have a speed symbol on the sidewall of the tire have a maximum speed rating of 87 mph (140 km/h). Michelin winter tires that do not have a speed symbol on the sidewall or tires with Q symbols have a speed rating of 100 mph (160 km/h).
IMPORTANT: The replacement tire speed rating should be equal to or higher than the OEM tire speed rating. If a lower speed rated tire is selected, then the vehicle top speed becomes limited to that of the lower speed rating selected. The customer must be informed of the new speed restriction and that the vehicle’s handling may be adversely impacted.

Qualifications & exceptions

  • Ratings do not apply to underinflated, overloaded, worn out, damaged, altered, improperly repaired or retreaded tires.
  • A lower replacement rating limits the vehicle to that speed.
Also annotated in the same passage (1)

Security & Safeguards · Procedure

Hitting a road hazard calls for an immediate inspection, visible damage or not

Road hazards and objects such as potholes, curbs, glass, metal, rocks, wood and debris can damage a tire and should be safely avoided. If the vehicle hits such a hazard, Michelin says to inspect the tires promptly. A damaged tire or wheel is replaced at once with a properly inflated spare, and all tires, including the spare, go to a tire professional, or to an authorized PAX System retailer for PAX System tires. A tire that hits a road hazard can be damaged without any visible surface sign, and impact damage can cause a sudden failure a day, a week or even months later. Air loss, unusual or localized wear or vibrations can also signal internal damage, and an impact with a curb, pothole or debris, or an unusual vibration, calls for replacing the tire and wheel with a properly inflated spare and visiting a qualified tire professional immediately.

Supporting quotations

INSPECT YOUR TIRES. DO NOT DRIVE ON A DAMAGED TIRE OR WHEEL.
WARNING
INSPECT AND REPLACE ANY VISIBLY DAMAGED TIRE IMMEDIATELY AFTER STRIKING ANY OBJECT IN THE ROAD.
Road hazards and objects in the road, such as potholes, curbs, glass, metal, rocks, wood, and debris, can damage a tire and should be safely avoided.
A tire that hits a road hazard or object can be damaged but not have any visible sign of damage on its surface. A tire damaged by an impact can suddenly fail a day, a week, or even months later.
If you suspect any damage to your tire or wheel from an impact with a curb, pothole, debris on the road, or any other road hazard or object, or if you feel or hear any unusual vibration, replace the tire and wheel with a properly inflated spare at once and immediately visit a qualified tire professional.

Qualifications & exceptions

  • The damage may be invisible and surface only later.

Security & Safeguards · Procedure

Inspect tires monthly and after any hazard, looking for bulges, cracks and penetrations

Michelin warns not to drive unnecessarily on a tire or wheel with any visible damage and tells owners to replace a damaged tire with a properly inflated spare at once and visit a Michelin Tire Retailer. Tires are inspected at least once per month and immediately after contacting a road hazard or object such as a curb, pothole or debris. The inspection includes the spare, checks inflation, and where a tire has lost two pounds or more of pressure, looks for penetration, valve leakage or wheel damage that may explain the loss. Owners look for bulges, cracks, cuts, penetrations and abnormal tire wear, particularly at the tread edges, since these may come from misalignment, road hazards or improper inflation, and a damaged tire must be inspected by a Michelin tire retailer at once because use could lead to tire failure and an accident. Tires wear faster under high speeds, hard cornering, rapid starts, sudden stops, poor roads and off-road use, so after driving on roads with holes, rocks or other objects Michelin says to examine the tires for cuts, bumps, bulges, penetrations or unusual wear before returning to normal or highway speeds.

Supporting quotations

INSPECTION
WARNING
DO NOT DRIVE UNNECESSARILY ON A TIRE OR WHEEL WITH ANY VISIBLE DAMAGE.
If you see any damage to a tire or wheel, replace it with a properly inflated spare at once and visit a Michelin Tire Retailer.
Inspect your tires at least once per month, and immediately after contacting any road hazard or object, such as a curb, a pothole, or debris.
If the pressure check indicates that one of your tires has lost pressure of two pounds or more, look for signs of penetration, valve leakage, or wheel damage that may account for the air loss.
Always look for bulges, cracks, cuts, penetrations, and abnormal tire wear, particularly on the edges of the tire tread. Any of these may be caused by misalignment, contact with road hazards or objects, or improper inflation. If any such damage is found, the tire must be inspected by your Michelin tire retailer at once.
All tires will wear out faster when subjected to high speeds, hard cornering, rapid starts, sudden stops, frequent driving on roads that are in poor condition, or off-road use.

Qualifications & exceptions

  • Inspection is monthly and immediately after any road hazard contact.
  • A loss of two pounds or more of pressure prompts a search for penetration, valve leakage or wheel damage.

Security & Safeguards · Procedure

Wear bars at 2/32 inch mark the end of safe tread life

MICHELIN tires have wear bars in the tread grooves at 2/32nds of an inch (1.6 mm). When the remaining tread matches the height of the wear bars, the tires must be replaced to ensure tire safety, and tires worn beyond that stage are extremely dangerous. The manual points to the Safe Driving pages on michelinman.com for illustrated tire inspection guidance.

Supporting quotations

TREAD WEAR BARS INDICATE THE LIMIT OF TREAD LIFE
MICHELIN® tires contain “Wear Bars” in the tire tread grooves at 2/32nds of an inch (1.6 mm). When the tread remaining matches the height of the Wear Bars, your tires must be replaced to ensure tire safety. Tires worn beyond this stage are extremely dangerous.
Also annotated in the same passage (1)

Security & Safeguards · Restriction or exception

Never load a tire beyond its sidewall rating or an axle beyond its weight rating

Michelin warns against driving on overloaded tires. The maximum load rating is molded on the tire sidewall and must not be exceeded, and the owner should follow the vehicle manufacturer's loading instructions so the tires are not overloaded. A tire loaded beyond its maximum allowable load for the application builds up excessive heat that may cause sudden tire failure and an accident, and the gross axle weight rating for any axle on the vehicle must not be exceeded.

Supporting quotations

LOADING
WARNING
DO NOT DRIVE ON OVERLOADED TIRES. DRIVING ON ANY OVERLOADED TIRE IS DANGEROUS.
The maximum load rating of your tires is molded on the tire sidewall. Do not exceed this rating. Follow the loading instructions of the manufacturer of your vehicle to ensure that your tires are not overloaded.
Tires loaded beyond their maximum allowable loads for the particular application will build up excessive heat that may result in sudden tire failure and an accident. Do not exceed the gross axle weight rating for any axle on your vehicle.

Qualifications & exceptions

  • The load limit is the sidewall rating; the axle limit is the gross axle weight rating.

Security & Safeguards · Procedure

Trailer towing needs retailer advice on tire size and pressure

Before towing a trailer, Michelin advises visiting a Michelin tire retailer for advice about the correct tire size and pressures, which depend on the type and size of trailer and hitch used. In no case may the maximum cold inflation pressure or the tire load rating be exceeded. The vehicle's tire information placard and the vehicle manufacturer's owner's manual hold further trailer-towing recommendations.

Supporting quotations

TRAILER TOWING
If you anticipate towing a trailer, you should visit your Michelin tire retailer for advice about the correct tire size and pressures.
Tire size and pressures will depend on the type and size of trailer and hitch utilized, but in no case must the maximum cold inflation pressure or tire load rating be exceeded.

Qualifications & exceptions

  • Tire size and pressure depend on the trailer and hitch.
  • The maximum cold inflation pressure and the load rating are absolute ceilings.

Security & Safeguards · Restriction or exception

A PAX or ZP tire at low pressure must not continue towing a trailer

Michelin calls operation of PAX or ZP tires at low or zero inflation with a trailer in tow dangerous and to be avoided. If the low pressure warning activates while towing, the driver stops, disconnects the trailer, and does not continue towing until the tire has been properly repaired and reinflated. A tire that cannot be repaired must be replaced with a new full-size, matching PAX or ZP tire and inflated properly before the trailer is towed again.

Supporting quotations

MICHELIN® PAX SystemTM Tires/Self-Supporting Zero Pressure (ZP) Tires and Trailer Towing
Operation of PAX® or ZP tires at low or zero inflation with a trailer in tow is dangerous and should be avoided.
If the low pressure warning indicator is activated when a trailer is in tow, stop, disconnect the trailer, and do not continue to tow the trailer until the tire has been properly repaired and re-inflated to the proper inflation.

Qualifications & exceptions

  • The warning indicator must have activated while a trailer is in tow.

Security & Safeguards · Procedure

Alignment and balance problems show as uneven wear or vibration and need checking at once

Michelin warns against driving on unevenly worn, out of alignment or unbalanced tires and says alignment and balancing are important for safety and maximum mileage. Uneven wear such as the inside shoulder wearing faster than the rest of the tread, or excessive vibration, may mean the vehicle is out of alignment or balance; these conditions shorten tire life and adversely affect handling, which could be dangerous. Irregular wear or vibration calls for an immediate alignment and balance check. Tires run underinflated show more wear on the shoulders than in the center, and the manual directs the owner to its tire rotation and replacement instructions.

Supporting quotations

WHEEL ALIGNMENT AND BALANCING ARE IMPORTANT FOR SAFETY AND MAXIMUM MILEAGE FROM YOUR TIRES.
WARNING
DO NOT DRIVE ON UNEVENLY WORN, OUT OF ALIGNMENT, OR UNBALANCED TIRES.
CHECK HOW YOUR TIRES ARE WEARING AT LEAST ONCE EACH MONTH
If your tires are wearing unevenly, such as the inside shoulder of the tire wearing faster than the rest of the tread, or if you detect excessive vibration, your vehicle may be out of alignment or balance.
Tires that have been run underinflated will show more wear on the shoulders than in the center of the tread.

Qualifications & exceptions

  • Underinflation shows up as shoulder wear rather than center wear.

Security & Safeguards · Restriction or exception

Keep the same size and type of tire on all four wheels and the spare

MICHELIN tires are radial tires, and Michelin says the same size and type of tire should be used on all four wheel positions for best, safe performance, with a full-size spare of the same size and type. Before mixing different tire types in any configuration, the owner should check the vehicle manufacturer's owner's manual for its recommendations. That check is especially important when mixing, matching or replacing tires on four-wheel drive vehicles, which may require special precautions.

Supporting quotations

TIRE MIXING
WARNING MIXED TIRES.
DO NOT DRIVE ON IMPROPERLY
MICHELIN® tires are radial tires. For best, safe performance, the same size and type of tire should be used on all four wheel positions, and the full size spare should be the same size and type.
It is especially important to check the vehicle manufacturer’s owner’s manual when mixing, matching, or replacing tires on 4-wheel drive vehicles, as this may require special precautions.

Qualifications & exceptions

  • Applies to mixing different tire types in any configuration.
  • Four-wheel drive vehicles may need special precautions.

Not stated here

  • The warning heading and the paragraph below it split the sentence 'DO NOT DRIVE ON IMPROPERLY MIXED TIRES' across two blocks.

Security & Safeguards · Restriction or exception

PAX and ZP tires must not be mixed with conventional tires

Michelin says PAX System tires should not be mixed with non-PAX tires, nor Self-Supporting Zero Pressure (ZP) tires with non-ZP tires, apart from temporary use of the properly inflated spare if the vehicle is so equipped.

Supporting quotations

PAX® SYSTEM™ TIRES SHOULD NOT BE MIXED WITH NON-PAX TIRES NOR SELF-SUPPORTING ZERO PRESSURE™ (ZP) TIRES WITH NON-ZP TIRES OTHER THAN THE TEMPORARY USE OF THE PROPERLY INFLATED SPARE IF THE VEHICLE IS SO EQUIPPED.

Qualifications & exceptions

  • Temporary use of the properly inflated spare is the stated exception.

Security & Safeguards · Procedure

M+S marks all-season tires; four dedicated winter tires are recommended

Tires meeting the US Tire Manufacturers Association definition of snow tires are marked M/S, M+S or M&S, normally called All-Season tires, and tires without that notation are not recommended for winter driving in regions that experience winter conditions. All-Season tires are designed to provide reliable performance in some winter conditions, but Michelin recommends four winter tires for optimal performance. Tires designated for severe winter conditions are marked on at least one sidewall with the letters M and S plus a mountain-with-snowflake pictograph. If such a tire must be temporarily replaced with one not so marked, the driver should immediately drive at a safe speed to a Michelin dealer so the spare returns to the trunk and a matching marked tire goes back on the vehicle.

Supporting quotations

WINTER DRIVING
Tires that meet the US Tire Manufacturers Association (USTMA) definition of snow tires are marked M/S, M+S, or M&S.
Tires without this notation are not recommended for winter driving in regions that experience winter conditions.
Although All-Season tires are designed to provide reliable performance in some winter conditions, the use of four winter tires is recommended for optimal performance.
Tires designated for use in severe winter conditions are marked on at least one sidewall with the letters “M” and “S” plus a pictograph of a mountain with a snowflake on it.
If such a tire needs to be temporarily replaced with a tire not so marked, you should immediately drive at a safe speed to a Michelin dealer to have the spare returned to the trunk and replaced on your vehicle by another tire with the letters “M” and “S” and the related pictograph.

Qualifications & exceptions

  • Tires without an M/S, M+S or M&S marking are not recommended for winter driving where winter conditions occur.
  • Severe winter tires carry M and S plus the mountain-snowflake pictograph.

Security & Safeguards · Procedure

Rotate every 6,000 to 8,000 miles, or sooner at the first sign of irregular wear

Michelin says tires must be rotated for maximum tread life, every 6,000 to 8,000 miles (10,000 to 12,000 km) or as the vehicle manufacturer specifies, whichever occurs more frequently, and monthly inspection for tire wear is recommended. Tires are rotated at the first sign of irregular wear, even before 6,000 miles (10,000 km). Directional tires must follow the arrows molded on the sidewall. Some TPMS units may not recognize that a tire has moved position, so the system should be reset as needed, and inflation may need adjustment after rotation because front and rear pressures can differ by load position. Vehicles with different size tires front and rear have rotation restrictions, and the vehicle owner's manual holds the proper rotation recommendations.

Supporting quotations

TIRE ROTATION AND REPLACEMENT
To obtain maximum tread life, you must rotate your tires.
You should rotate your tires every 6,000-8,000 miles (10,000-12,000 km) or as specified by your vehicle manufacturer, whichever occurs more frequently.
Your tires should be rotated at the first sign of irregular wear, even if it occurs before 6,000 miles (10,000 km).
When rotating tires with a directional tread pattern, observe the arrows molded on the sidewall that show the direction in which the tire should rotate.
Some Tire Pressure Monitoring Systems (TPMS) may not recognize that a tire has been moved to a different position on your vehicle. Make certain that your TPMS system is reset, if necessary, so as to correctly identify the location of each tire on your vehicle.
Some vehicles may have tires of different sizes mounted on the front versus the rear axles, and these different tires have rotation restrictions.

Qualifications & exceptions

  • The shorter of the 6,000-8,000 mile interval and the vehicle manufacturer's specification applies.
  • Staggered front and rear sizes carry rotation restrictions.

Security & Safeguards · Procedure

A full-size spare joins the five-tire rotation only after inspection

Full-size spare tires, as distinct from temporary spares, of the same size and construction should be used in a five-tire rotation and inspected by a tire professional during routine tire inspection, and spare tires are always inspected before installation. Before the spare joins the rotation, its inflation pressure is checked and it is examined for cracking or other damage. A damaged or underinflated tire is not used unless there is no other option, in which case the driver should drive only as slowly as is safely possible until the tire can be inflated and checked by a professional. Michelin says to follow the vehicle manufacturer's recommended rotation pattern, or see a qualified tire professional if none is available.

Supporting quotations

Full-size Spare
Full-size spare tires (not temporary spares) of the same size and construction should be used in a five-tire rotation and should be inspected by a tire professional during routine tire inspection.
Always check the inflation pressure of the full-size spare and look for any indication of cracking or other damage immediately before incorporating the spare into rotation.
Follow the vehicle manufacturer’s recommended pattern for rotation. If such a recommendation is unavailable, see a qualified tire professional.

Qualifications & exceptions

  • Applies to full-size spares, not temporary spares.
  • The spare is inspected and its pressure checked immediately before it joins the rotation.

Security & Safeguards · Company practice

Replace all four tires together, or put a pair of new tires on the rear

Michelin says all four tires should be replaced at the same time. If only two tires are replaced, the new ones should go on the rear, because deeper tread on the rear axle provides better handling, wet grip and water evacuation, helping avoid oversteer and loss of stability on wet surfaces. Deeper tread on the front axle can improve wet straight-line braking and stopping distance. If only two tires are replaced, Michelin generally recommends installing them on the rear axle unless a tire service professional or the consumer prefers otherwise.

Supporting quotations

Replacement of Two Tires
All four tires should be replaced at the same time.
However, if only two tires are replaced, the new ones should be put on the rear. Deeper tread tires on the rear axle provide better handling, wet grip and evacuate water, thereby helping to avoid oversteer and loss of vehicle stability on wet surfaces.
Deeper tread tires on the front axle can improve wet straight line braking and stopping distance.
If only two tires are being replaced, Michelin generally recommends they be installed on the rear axle in the absence of a tire service professional’s recommendation or consumer’s preference to the contrary.

Qualifications & exceptions

  • The rear-axle recommendation yields to a contrary professional recommendation or consumer preference.

Security & Safeguards · Context

SUVs and light trucks roll over more easily, and modifications raise the risk

Because of their size, weight and higher center of gravity, SUVs and light trucks do not handle like automobiles, and Michelin says failing to operate them properly and safely can increase the likelihood of vehicle rollover. Modifications to tire size, tire type, wheels or suspension can change the vehicle's handling characteristics and further raise the rollover risk. Whether the vehicle keeps its original equipment configuration or has been modified, Michelin says to drive safely, avoid sudden sharp turns and lane changes, and obey all traffic laws, since otherwise the driver may lose control, causing an accident and serious injury or death.

Supporting quotations

CUSTOMIZATION OF TIRES, WHEELS, OR SUSPENSION ON SUVS AND LIGHT TRUCKS
Due to their size, weight and higher center of gravity, vehicles such as SUVs and light trucks do not have the same handling characteristics as automobiles. Because of these different characteristics, failure to operate your SUV or truck in a proper and safe manner can increase the likelihood of vehicle rollover.
Modifications to your SUV or truck tire size, tire type, wheels or suspension can change your vehicle’s handling characteristics and further increase the likelihood of vehicle rollover.
Whether your SUV or truck has the original equipment configuration for tires, wheels and suspension or whether any of these items have been modified, always drive safely, avoid sudden, sharp turns or lane changes and obey all traffic laws.

Qualifications & exceptions

  • Applies whether the vehicle is in its original configuration or modified.

Security & Safeguards · Procedure

A punctured tire is demounted, inspected and repaired only within narrow limits

Michelin warns against driving on improperly repaired tires or on mismatched tires and rims, and says to see a MICHELIN tire retailer, or another qualified tire professional if none is readily available, whenever a repair is needed. A punctured MICHELIN tire is demounted and thoroughly inspected for damage. A tread area puncture on a passenger or light truck tire can be repaired only if the hole is no more than 1/4 inch in diameter, no more than one radial cable per casing ply is damaged, and the tire has not been damaged further by the puncturing object or by running underinflated. Repairs consistent with those guidelines follow the US Tire Manufacturers Association's recommended procedures.

Supporting quotations

TIRE REPAIRS
WARNING
DO NOT DRIVE ON IMPROPERLY REPAIRED TIRES OR ON MISMATCHED TIRES AND RIMS.
WHENEVER A REPAIR IS NEEDED, IMMEDIATELY SEE YOUR MICHELIN® TIRE RETAILER OR, IF ONE IS NOT READILY AVAILABLE, ANOTHER QUALIFIED TIRE PROFESSIONAL
A tread area puncture in any MICHELIN® passenger or light truck tire can be repaired if the puncture hole is not more than 1/4" in diameter, not more than one radial cable per casing ply is damaged, and the tire has not been damaged further by the puncturing object or by running underinflated.

Qualifications & exceptions

  • Puncture hole no more than 1/4 inch in diameter.
  • No more than one radial cable per casing ply damaged.
  • No further damage from the object or from running underinflated.

Security & Safeguards · Procedure

Repairs use a plug and inside patch with the tire off the rim, and never below 2/32 inch

Repairs of all tires must combine a plug with an inside patch, and MICHELIN tires, including PAX System tires, must be removed from the wheel for inspection before repair. Plug-type repairs made on a tire still mounted on a wheel are improper and can cause an accident, as is any repair done without removing the tire from the rim. An improperly repaired tire may leak air or let air, moisture and contaminants into its structure, and it can fail suddenly later. Michelin says never to repair a tire with less than 2/32nds of an inch of tread remaining, because at that depth the tire is worn out and must be replaced.

Supporting quotations

Repairs of all tires must be of the combined-plug-and-inside-patch type.
Your MICHELIN tires (including Michelin PAX System™ tires) must be removed from the wheel for inspection prior to repair.
Plug-type repairs made on a tire that remains mounted on a wheel are improper and can result in an accident.
Never repair a tire with less than 2/32nds of an inch of tread remaining. At this tread depth, the tire is worn out and must be replaced.

Qualifications & exceptions

  • The tire must come off the rim for inspection and repair.
  • A tire with less than 2/32nds of an inch of tread is not repaired.

Security & Safeguards · Procedure

Store tires cool, dry and indoors, and take the weight off for a month or more

Tires carry materials that protect their outer surfaces from ozone and weather checking, and those materials migrate to the surface as the tire rolls and flexes during normal use. When tires sit outdoors unused for a month or more, their surfaces dry out and become more susceptible to ozone and weather checking, and the casing becomes susceptible to flat spotting. Michelin therefore says tires should be stored in a cool, dry, clean, indoor environment, with the weight removed, by raising the vehicle or taking the tires off it, if storage lasts a month or more. Failing to store tires this way could damage them or age them prematurely and lead to sudden tire failure. Stored tires are kept away from heat and ozone sources such as hot pipes and electric generators, and on surfaces free of grease, gasoline or other substances that could deteriorate the rubber.

Supporting quotations

STORAGE
For this reason, tires should always be stored in a cool, dry, clean, indoor environment.
If storage is for one month or more, eliminate the weight from the tires by raising the vehicle or by removing the tires from the vehicle.
When tires are stored, be sure they are placed away from sources of heat and ozone such as hot pipes and electric generators.
Be sure that surfaces on which tires are stored are clean and free from grease, gasoline or other substances which could deteriorate the rubber.

Qualifications & exceptions

  • Weight removal applies to storage of one month or more.
  • Storage surfaces must be clean and free of grease, gasoline and similar substances.

Security & Safeguards · Context

Trunk heat is a reason to include the spare in the rotation

Michelin explains that temperatures in a vehicle's closed trunk, especially in sunny areas, can become high enough over a sustained period to cause small cracks or other property changes in a tire stored there. Such changes accumulate and can weaken the tire and, especially if it is not kept properly inflated, make it unsafe to use when needed. That is one reason the spare tire should be included in the tire rotation schedule.

Supporting quotations

One reason why your spare tire should be included in the tire rotation schedule is that temperatures in a vehicle’s closed trunk, especially in sunny geographical areas, can become high enough so that, over a sustained period, they can cause small cracks or other changes to the properties of a tire stored in the trunk.

Security & Safeguards · Procedure

Mounting needs trained professionals, sound wheels and no mismatched parts

Tire mounting can be dangerous and must be done by professionally trained persons using proper tools and procedures specified by the US Tire Manufacturers Association. MICHELIN PAX System tires must be mounted and dismounted only by specially trained, authorized MICHELIN PAX System retailers using equipment designed for the system. Tires go on wheels of the correct size and type in good, clean condition, because bent, chipped, rusted or corroded wheels may damage a tire, and the inside of the tire must be free of foreign material. Mismatched tires and rims can explode during mounting or fail dangerously on the road. A tire mounted by error on the wrong-sized rim is not remounted on the proper rim but scrapped, because it may have been internally damaged by being stretched.

Supporting quotations

PROPER TIRE MOUNTING
Tire mounting can be dangerous and must be done by professionally trained persons using proper tools and procedures as specified by the US Tire Manufacturers Association (USTMA).
MICHELIN® PAX System™ tires must be mounted and dismounted only by specially trained, authorized MICHELIN PAX System retailers, utilizing equipment designed for the MICHELIN PAX System.
Your tires should be mounted on wheels that are the correct size and type and are in good, clean condition. Wheels that are bent, chipped, rusted (steel wheels) or corroded (alloy wheels) may cause tire damage.
Mismatched tires and rims can explode during mounting. Also, mismatched tires and rims can result in dangerous tire failure on the road.
If a tire is mounted by error on the wrong-sized rim, do not remount it on the proper rim – scrap it.

Qualifications & exceptions

  • PAX System tires require specially trained, authorized PAX System retailers.

Security & Safeguards · Procedure

Fit new valves, use tubeless wheels and balance every tire and wheel assembly

Old valves may leak, so when new tubeless tires are mounted Michelin says to install new valves of the correct type. Tubeless tires must be mounted only on wheels designed for tubeless tires, meaning wheels with safety humps or ledges, and the PAX System valve stem and pressure sensor combination must be in good condition. Valve caps capable of containing the tire's inflation should always be used, since the cap is the primary seal against air loss if the valve core leaks. Each tire and wheel assembly should be balanced for proper performance and to maintain tire warranty coverage, because unbalanced assemblies may cause steering difficulties, a bumpy ride and irregular tire wear.

Supporting quotations

Old valves may leak. When new tubeless tires are mounted, have new valves of the correct type installed.
Tubeless tires must be mounted only on wheels designed for tubeless tires, i.e., wheels that have safety humps or ledges.
Always utilize valve caps capable of containing the tire’s inflation, should the valve core leak. The valve cap is the primary seal against air loss.
Each tire and wheel assembly should be balanced to ensure proper tire and vehicle performance and to maintain tire warranty coverage.
Tires and wheel assemblies that are not balanced may cause steering difficulties, a bumpy ride, and irregular tire wear.

Qualifications & exceptions

  • Tubeless tires require wheels with safety humps or ledges.

Security & Safeguards · Restriction or exception

PAX System tires and wheels cannot be mixed with any other system

MICHELIN PAX System wheels differ from all other wheels. Michelin says never to attempt mounting a non-PAX System tire on a PAX System wheel or a PAX System tire on a non-PAX System wheel, which could cause serious injury or death. Every PAX System component, meaning tire, wheel, support ring, pressure sensor and gel, must be used, properly functioning and correctly installed by an Authorized PAX System retailer, and the PAX System must be used on all wheel positions. After a low or zero pressure driving event the PAX System tire and wheel may be hot to the touch, and Michelin says to let the tire cool before handling it.

Supporting quotations

SPECIAL MOUNTING INSTRUCTIONS FOR MICHELIN PAX SYSTEMTM TIRES
MICHELIN PAX System™ wheels differ from all other wheels. Never attempt to mount a non-PAX System tire on a PAX System wheel, or a PAX System tire on a non-PAX System wheel. Attempting to do so could cause serious injury or death.
All PAX System components (tire, wheel, support ring, pressure sensor and gel) must be utilized. Never utilize a PAX System tire and wheel without every other properly functioning component part, correctly installed by an Authorized PAX System retailer.
The PAX System must be used on all wheel positions.
After a low or zero pressure driving event, the PAX System tire and wheel may be hot to the touch. Always allow a PAX System tire to cool before attempting to handle it.

Qualifications & exceptions

  • All PAX System components must be used together.
  • The system must be installed by an Authorized PAX System retailer on all wheel positions.

Security & Safeguards · Procedure

ZP tires need trained mounting and must cool before anyone handles them

ZP tires can be more difficult to mount than conventional tires and should be mounted and demounted only by a properly trained tire professional. Because they can generate tremendous heat when run at low or zero pressure, Michelin says to always allow a ZP tire to cool before attempting to handle it, and failure to do so could result in injury or death. MICHELIN ZP tires are tubeless tires designed to operate in emergency conditions at low or zero inflation.

Supporting quotations

SPECIAL MOUNTING INSTRUCTIONS FOR SELF- SUPPORTING ZERO PRESSURE™ (ZP) TIRES
ZP tires can be more difficult to mount than conventional tires. They should be mounted and demounted only by a properly trained tire professional.
ZP tires can generate a tremendous amount of heat when run at low or zero pressure. ALWAYS ALLOW A ZP TIRE TO COOL BEFORE ATTEMPTING TO HANDLE IT. FAILURE TO DO SO COULD RESULT IN INJURY OR DEATH.
Michelin® ZP tires are tubeless tires designed to operate in emergency conditions at low or zero inflation.

Qualifications & exceptions

  • Mounting and demounting by a properly trained tire professional only.

Security & Safeguards · Restriction or exception

SH-M designated ZP tires need SH-M wheels to keep zero-pressure capability

Some MICHELIN ZP tires perform with zero pressure capability only when mounted on special SH-M (Symmetric Hump-Modified) wheels, and those tires bear the SH-M designation immediately after the ZP designation on the sidewall. Michelin warns against mounting ZP tires with the SH-M designation on standard wheels, because in such applications the tires may become unserviceable at low or zero pressure and cause serious injury or death.

Supporting quotations

MICHELIN® SELF SUPPORTING ZERO PRESSURE™
(ZP) TIRES AND SPECIAL SH-M (SYMMETRIC HUMP- MODIFIED) WHEELS
Some MICHELIN® ZP tires can perform with zero pressure capability only when mounted on special SH-M wheels. These tires bear the SH-M designation immediately following the ZP designation on the sidewall of the tire.
WARNING
DO NOT MOUNT ZP TIRES WITH THE SH-M DESIGNATION ON STANDARD WHEELS. IN SUCH APPLICATIONS, THE TIRES MAY BECOME UNSERVICEABLE AT LOW OR ZERO PRESSURE, CAUSING SERIOUS INJURY OR DEATH.

Qualifications & exceptions

  • The SH-M marking on the sidewall identifies tires that require SH-M wheels.

Security & Safeguards · Restriction or exception

TRX tires fit only special TR or JM wheels

The TRX tire is a tubeless tire that must be mounted only on special wheels (TR or JM type) with millimetric seat diameter. Mounted on standard wheels, TRX tires will not retain air because of an air escape feature designed into the bead area of these tires.

Supporting quotations

SPECIAL MOUNTING INSTRUCTIONS FOR TRXTM TIRES
The TRX™ tire is a tubeless tire that must only be mounted on special wheels (TR or JM type) with millimetric seat diameter. If TRX tires are mounted on standard wheels, they will not retain air due to an air escape feature designed into the bead area of these tires.

Qualifications & exceptions

  • Only TR or JM type wheels with millimetric seat diameter.

Security & Safeguards · Restriction or exception

Do not fit tubes to TRX tires, and use them on all wheel positions

Michelin tells owners not to try to override the TRX bead feature by mounting TRX tires with tubes. The MICHELIN TRX must be used on all wheel positions, and Michelin warns that failing to follow this instruction can cause an accident with serious injury, death and property damage.

Supporting quotations

WARNING
DO NOT TRY TO OVERRIDE THIS FEATURE BY MOUNTING TRX TIRES WITH TUBES. THE MICHELIN® TRX MUST BE USED ON ALL WHEEL POSITIONS.

Qualifications & exceptions

  • The TRX must be used on all wheel positions.

Security & Safeguards · Procedure

Temporary spare tires follow the vehicle manufacturer's instructions

When using any temporary type spare tire, Michelin says to be sure to follow the vehicle manufacturer's instructions.

Supporting quotations

TEMPORARY TYPE SPARE TIRES
When using any temporary type spare tire, be sure to follow the vehicle manufacturer’s instructions.

Security & Safeguards · Procedure

The DOT code identifies where and when a tire was made

The DOT symbol certifies the manufacturer's compliance with U.S. Department of Transportation tire safety standards, and beside it sits the tire identification or serial number. The first two characters identify the plant, the next two reflect the tire size, one to four following digits may carry a manufacturer's descriptive code, and the last characters identify the week and year of manufacture. For the 1990-1999 decade MICHELIN tires are marked with a triangle pointing to the last three numeric characters, and tires produced after July 2000 carry an additional decade digit: 2800 means the 28th week of 2000 and 0201 the 2nd week of 2001. Where the last digits contain three numeric characters and no triangle, Michelin says to consult a qualified tire professional to determine the year of manufacture. The manual also shows the older and newer DOT layouts, including the 13-digit format phased in from 2018 and in effect for all plants by 2025.

Supporting quotations

READING THE DOT
DOT XXXX XXXX XXX (prior to August 2000)
(1990-1999) DOT XXXX XXXX XXX
DOT XXXX XXXX XXXX (after July 2000 to 2025)
DOT XXXXX XXXX XXXX (transition to 13 digits beginning 2018; in effect for all plants by 2025)
THE DOT
The “DOT” symbol certifies a tire manufacturer’s compliance with U.S. Department of Transportation tire safety standards.
The first two characters identify the plant where the tire was manufactured. The next two characters reflect the tire size.
For example, 2800 means the tire was produced during the 28th week of 2000; 0201 during the 2nd week of 2001.
If the last digits of your DOT number contain three numeric characters and are not marked with a triangle, consult a qualified tire professional to determine the year of manufacture.

Qualifications & exceptions

  • After July 2000 the last digits add a decade digit.
  • A three-digit code without a triangle requires professional interpretation.

Security & Safeguards · Procedure

Replace tires in service ten years or more, and have five-year-old ones inspected yearly

Michelin explains that a tire's materials evolve with weather, storage and use, so the serviceable life of a specific tire cannot be predicted in advance. Passenger car and light truck tires, including spares, should be inspected regularly by a qualified tire specialist such as a Michelin retailer, and tires in use five years or more should keep being inspected by a specialist at least annually. Changes such as increased air loss, noise or vibration may indicate the tire should come out of service to prevent failure. Calendar age alone cannot tell when a tire should be replaced, but while most tires need replacement before ten years, Michelin recommends replacing any tire in service ten years or more from the date of manufacture, including spares, as a precaution, even if it looks serviceable and has not reached the legal wear limit. For tires that came on an original equipment vehicle, the vehicle manufacturer's tire replacement recommendations apply when specified, but not beyond ten years. The date of manufacture is on the sidewall in the DOT code, which ends with the week and year, for example a code ending 2214 for the 22nd week of 2014.

Supporting quotations

SERVICE LIFE FOR PASSENGER CAR AND LIGHT TRUCK TIRES INCLUDING SPARE TIRES
it is recommended that passenger car and light truck tires, including spare tires be inspected regularly by a qualified tire specialist, such as a Michelin tire retailer, who will assess the tire’s suitability for continued service.
Tires which have been in use for 5 years or more should continue to be inspected by a specialist at least annually.
While most tires will need replacement before they achieve 10 years, it is recommended that any tires in service 10 years or more from the date of manufacture, including spare tires, be replaced with new tires as a precaution even if such tires appear serviceable and even if they have not reached the legal wear limit.
For tires that were on an original equipment vehicle (i.e., acquired by the consumer on a new vehicle), follow the vehicle manufacturer’s tire replacement recommendations, when specified (but not to exceed 10 years).
It is impossible to predict when tires should be replaced based on their calendar age alone.
For example, a DOT code ending with “2214” indicates a tire made in the 22nd week of 2014.

Qualifications & exceptions

  • Tires in use five years or more are inspected by a specialist at least annually.
  • Ten years is a precautionary replacement point, not a prediction based on calendar age alone.
  • Original equipment vehicle recommendations apply when specified, not beyond ten years.

Security & Safeguards · Procedure

The closing checklist collects the manual's safety precautions

Michelin closes with a list of precautions to avoid tire damage and possible accident: inspect tires at least monthly and immediately after striking any road hazard; check pressure at least once a month when tires are cold and before every long trip; never underinflate or overinflate; never overload the vehicle or tires; obey legal speed limits and drive at a reasonable speed for road and weather conditions; avoid potholes, obstacles, curbs and pavement edges; avoid excessive wheel spinning; replace a damaged tire with a properly inflated spare and visit a qualified tire professional at once; keep tires and wheels aligned, balanced and rotated; have mounting and repairs done by a tire professional; and ask a Michelin tire retailer with any questions. Michelin warns that failing to follow any of these precautions can lead to erratic vehicle behavior or tire damage, possibly resulting in an accident.

Supporting quotations

REMEMBER... TO AVOID DAMAGE TO YOUR TIRES AND POSSIBLE ACCIDENT:
INSPECT TIRES AT LEAST MONTHLY, AND IMMEDIATELY AFTER STRIKING ANY ROAD HAZARD.
CHECK TIRE PRESSURE AT LEAST ONCE EACH MONTH WHEN TIRES ARE COLD AND BEFORE EVERY LONG TRIP.
NEVER UNDERINFLATE OR OVERINFLATE A TIRE.
NEVER OVERLOAD YOUR VEHICLE AND TIRES.
ALWAYS OBEY LEGAL SPEED LIMITS AND DRIVE AT A SPEED THAT IS REASONABLE UNDER THE ROAD AND WEATHER CONDITIONS.
AVOID DRIVING OVER POTHOLES, OBSTACLES, CURBS OR EDGES OF PAVEMENT.
AVOID EXCESSIVE WHEEL SPINNING.
IF YOU SEE ANY DAMAGE TO A TIRE, REPLACE THE TIRE WITH A PROPERLY INFLATED SPARE AND VISIT A QUALIFIED TIRE PROFESSIONAL AT ONCE.
KEEP TIRES AND WHEELS PROPERLY ALIGNED, BALANCED, AND ROTATED.
HAVE MOUNTING AND REPAIRS DONE BY A TIRE PROFESSIONAL.
IF YOU HAVE ANY QUESTIONS, CONTACT YOUR MICHELIN TIRE RETAILER.
FAILURE TO FOLLOW ANY OF THE RECOMMENDED PRECAUTIONS CONTAINED IN THIS OWNER’S MANUAL CAN LEAD TO ERRATIC VEHICLE BEHAVIOR OR TIRE DAMAGE, POSSIBLY RESULTING IN AN ACCIDENT.